Home > Windows 98 > Windows 98 Startup Error Messages

Windows 98 Startup Error Messages

Contents

Other error messages If you are experiencing other error messages it is likely these errors are being caused by the software program you are running, or hardware device you are attempting Instead, these errors can be caused by any segment of code, even at the system or device driver level.The address that the program tries to access may be illegal for any Issue with hardware device If you are having difficulties with a hardware device see the basic troubleshooting section for steps that can be taken to help resolve your hardware issues. Additional information about how to backup and restore the Registry using the scanreg utility can be found on our Registry page. his comment is here

Setup cannot create files on your startup drive and cannot set up Windows 98. If your computer has a virus protection program installed, make sure it is up to date and that no viruses are being detected. by Cursorcowboy / May 29, 2005 11:10 PM PDT In reply to: Bootdisk is not being recognized by computer 1. Try the clean-install method for setup.

Windows 98 Startup Problems

When Windows generates Windows Protection Errors, the system will almost always boot in Safe Mode.The first thing that I recommend doing to fix the problem is to scan for viruses. Try installing Windows 98 from DOS.Setup does not have enough conventional memory to check your computer's hard disks. The first thing I recommend you do is create a boot disk that you can use to repair the error. Like someone said,you use the floppy too get into DOS to format,go from drive C too D too set up with CD ROM.Their are two Boot floppys, I use the one

Forums > Tech Support > Windows 98 Error message at startup! "Windows 98 Error message at startup!" Started 6/15/2007 by admin in Tech Support Forum (5 posts) 1 See document CH000546 for additional information on what drivers should be updated on your computer. Rename or move your current DESKTOP folder, and then run Setup again. Was this page useful?

Once the system is up and running make sure the CD-ROM drive and any other essential devices are accessible and working correctly. Windows 98 Not Booting To create a Startup disk/Emergency Boot Disk (EBD) (Click to see an example screenshot), click Start, Settings, Control Panel, Add/Remove Programs, Startup Disk, Create Disk..., and follow the instruction.6. Boot the system with this EBD and ensure everything operates properly. http://www.cpucare.net/OS/98/Errors/Troubleshooting%20Windows%2098%20Setup%20and%20Install%20Errors.htm There may be too many files in the root directory of your startup drive, or your startup drive letter may have been remapped (SU0018):The root folder of a drive holds a

Note: If the system's CMOS is set for booting from the hard disk first, you must change the options so the system boots first from a floppy drive.g. The three ways easy ways to make a boot diskette:a) Config Panel>Add and Remove softwareb) locate and run bootdisk.bat on your PCc) go to www.bootdisk.com, download a program to make it, This will use all SCANDISK options to fix the problem. Type the following commands, pressing Enter upon completion of each line.

Windows 98 Not Booting

READ MORE © CBS Interactive Inc.  /  All Rights Reserved. http://www.tomshardware.com/forum/184043-48-windows-startup-boot-problems In this article, I’ll share some of these techniques with you.Windows won’t load at allIf Windows doesn’t load, the problem is usually related to hard disk corruption. Windows 98 Startup Problems When up and running again, go and find it! Windows 98 Startup Menu This forum has been preserved for reference and is not active.

Next, open a Command Prompt window and enter the following commands:SYS A:C:CD\WINDOWS\SYSTEM\COMMANDCOPY FDISK.* A:COPY FORMAT.* A:COPY SYS.* A:EXITThere are other files, such as XCOPY32, that may also be helpful should you These errors are often caused by low conventional memory. Whatever the cause, the important part is fixing it. Other causes are that the memory address is flagged as read only or the address may not exist at all. Windows 98 Won T Boot

Most of the system’s device drivers aren’t loaded, and neither are any of your startup applications. by Kees Bakker / May 29, 2005 4:19 PM PDT In reply to: Bootdisk is not being recognized by computer Although it's nice to have working boot disk, it's not necessary Essentially, this virtual drive emulates a physical hard drive on a system and is created where the EBD.CAB files are uncompress:Attrib.exe - Add or remove file attributes Chkdsk.exe - A simpler weblink Check if the address is correct.

Flag Permalink This was helpful (0) Collapse - Use the right floppy disk? Either choose the option to replace the file and reboot or cancel and close all running applications. Then type the scanreg /fix (or probably you need scanreg /restore, I think) commands Toni suggested.

Setup cannot continue on this system configuration.Click OK to quit Setup:Install Windows 98 from DOS.Not Enough Memory: Not enough conventional memory to continue the installation.

And that goes wrong.To boot in MS-DOS, you press ctrl or f8 to get into the boot menu and choose MS-DOS (by head: 5, but have a look at the menu Ensure that if programs are loading automatically, the errors are not associated with these programs. After the ?.EXE has downloaded, find and double-click it. (? To do so, go to another machine that’s running an identical version of Windows 98.

by Kees Bakker / May 29, 2005 10:04 PM PDT In reply to: Unable to get the computer up and running in Safe Mode To boot in Safe Mode, you press Sorry, there was a problem flagging this post. If you still have problems after this, SCANDISK /ALL /SURFACE. Insert a floppy disk into drive A.c.

Comment out lines in CONFIG.SYS and AUTOEXEC.BAT one-by-one until you have enough memory to continue. Keep in mind that the word "program" doesn’t necessarily refer to an application, such as Microsoft Word. Make the changes you need, then close the main sysedit window and select yes to the prompts....Then reboot.

About Contact Us Archives Glossary Forums Archive Advertise AdChoices PCMag.com If you have disk overlay software installed, try installing Windows 98 from DOS.Standard Mode: Invalid DPMI returnStandard Mode: Fault in MS-DOS ExtenderStandard Mode: Bad Fault in MS-DOS ExtenderStandard Mode: Unknown stack