Home > Windows Error > Windows Error On Easymatchqc

Windows Error On Easymatchqc

Installation of the software is no problem but when I want to open EasyMatch I get the following error: ‘EasyMatchQC MFC Application has encountered a problem and needs to close. As default, an Access-type database “EZMQC.mdb” is created upon installation, and “AutoSave Measurement” checked to save all measurements as a backup. Locate the following files and drag them to the Recycling Bin. Start up the EZMQC program again and you will be prompted to re-install your sensor.

Do not remove any other files from this folder. Your cache administrator is webmaster. What can I do?” FAQ: “Yesterday in the morning our HunterLab instrument was working fine, but in the afternoon there was an electrical problem at the factory. The system returned: (22) Invalid argument The remote host or network may be down. https://support.hunterlab.com/hc/en-us/articles/204214289-EasyMatch-QC-error-message-Operation-must-use-updateable-query-

Your cache administrator is webmaster. We are sorry for the inconvenience.' Can you help? Choose Repair and complete the Repair Wizard.

Navigate toC:\Windows\System32. If outdated or incompatible software on your computer places the wrong version of a shared .dll file in the C:\Windows\System32 folder, you might see one of the messages below: "iTunes was If iTunes won't launch or you see Error 7 (Windows error 193)again, continue with the steps in the next section. Also avoid using the File/Save Measurement to Database command.

This issue went away then." This would also resolve the issue.   Was this article helpful? 0 out of 0 found this helpful Facebook Twitter LinkedIn Google+ Comments facebook twitter google All rights reserved. Please advise." Other variations: "MSVBVM50.DLL missing from Windows 7 64 bit" "MSVBVM50.DLL missing from Windows 8.1" "MSVBVM50.dll Not Found" The error message "The program can't start because MSVBVM50.DLL is missing from https://measuretruecolor.hunterlab.com/2012/06/07/easymatchqc-mfc-application-has-encountered-a-problem/ Please try the request again.

Re-install the sensor again at Sensor/Install-Configure; The "sensors.dat” file will be re-created when you do this and the software should then function correctly. Reinstall iTunes. Note that no measurements can be saved to the database for this user until the proper Windows privileges are assigned by your System Administrator. Archives June 2016 April 2016 October 2015 June 2015 April 2015 September 2014 August 2014 July 2014 June 2014 May 2014 April 2014 March 2014 February 2014 January 2014 October 2013

Privacy Policy Terms of Use Sales and Refunds Site Map Contact Apple New Zealand (English) JavaScript isn't enabled in your browser, so this file can't be opened. http://dpeeip.myfirewall.org/C9-9 Terms & Conditions Sitemap Privacy Powered by Zendesk Measure True Color HunterLab - the world's resource for color and appearance measurement Search Main menu Skip to primary content Homeapplication notesterminologysourcescontact usabout The error message is rare and not specific, but it appears EasyMatch QC is trying to read a corrupted sensor file. The system returned: (22) Invalid argument The remote host or network may be down.

After you drag the files to the Recycling Bin, try performing a repair on both installed versions of Apple Application Support (64 and 32-bit). Also, when I perform certain functions in EasyMatch QC I receive a run time error and the software closes.” The message can come from more than one source but the most Check if the address is correct. For EasyMatch QC/ER< 4.20 go to C:\Program Files\HunterLab\EasyMatchQC\Sensors folder.

When the UltraScan PRO was turned on had a problem, the following error message appeared. ‘EasyMatch QC Application has encountered a problem and needs to close. If you can't locate a file, skip it and go to the next file. Please upgrade to a supported browser.DismissFileEditViewToolsHelpAccessibilityDebugSee new changesAccessibilityView onlyToggle screen reader support ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: Bookmark the permalink.

For EZMQC/ER versions 4.20 and higher (Help/About), use Windows Explorer to go to C:\HunterLab\EasyMatchQC\Sensors folder. Delete the "sensors.dat" file found there. Other company and product names may be trademarks of their respective owners.

iTunes requires both 64 and 32-bit versions of Apple Application Support.Navigate to the Add/Remove programs list in the Control Panel then follow these steps: Click Apple Application Support 32-bit to select

If a System Administrator is not immediately available to assign the required Windows privileges, you may temporarily eliminate appearance of this error message by selecting the Options menu, System Configuration/Data Storage, Repeat steps 1 through 3 for Apple Application Support 64-bit. Please reinstall iTunes. Submit a request Sign in Community Support Center Home Main Hunterlab Website Create a Support Request Hunterlab Frequently Asked Questions About our Instruments and Accessories EasyMatch QC error message - “Operation

This means that the cache was not able to resolve the hostname presented in the URL. If the User logged into the computer does not have full read/modify/write privileges to the database file or the folder where this database is kept, this message will be triggered whenever Fill in your details below or click an icon to log in: Email (required) (Address never made public) Name (required) Website You are commenting using your WordPress.com account. (LogOut/Change) You are This means that the cache was not able to resolve the hostname presented in the URL.

To fix this have a System Administrator for the computer grant EZMQC+ER Users the required privileges by locating the c:\HunterLab\EasyMatchQC folder (or EasyMatchQC-ER Client if using EZMQ-ER software), right-clicking on the Completely remove iTunes and related software componentsfrom your computer, then reboot your computer. Have the customer search their PC for the file "MSVBVM50.DLL". If the issue persists,contact Apple Support for more help.

Yes No Thanks - please tell us how to help you better.